• TEL: 0086-13083697781

s550mc thickness

Get Price

We can supply you need s550mc thickness.

EN 10149-2 - SSAB

EN 10149-2. EN 10149-2 is the European Standard for hot-rolled flat products made of high yield strength thermo-mechanically rolled steels for cold forming. Flat products - Materials TradingThickness 1,2 - 25,4mm; Width 1000-2020mm; Typical Grades:DD11, DD12, DD13, DD14 as per DIN EN 10111:2008; S235, S275, S355 as per DIN EN 10025-2:2004; S315MC, S355MC, S420MC, S460MC, S500MC, S550MC, S600MC as per DIN EN 10149-2:2013; Hot rolled steel sheet in coils pickled and oiled available as well. All mentioned products can be cut into

HSLA steels - ArcelorMittal

Steels in the HSLA (High Strength Low Alloy) range are hardened by a combination of precipitation and grain size refining, resulting in high strength with low alloy content. This enhances weldability and choice of coatings, since these steels exhibit neither weld-zone softening nor grain coarsening. These grades are particularly suitable for structural components such as suspension systems Higher-strength steel > Heavy plate > Products THICKNESS 1 from _ to in mm WIDTH 1 from _ to in mm THICKNESS 1 from _ to in mm WIDTH 1 from _ to in mm ; perform ® 500 :S500MC - - 2.0 20.0 :2,000 :perform ® 550 :S550MC - - 2.0 8.5 :1,850 : Hot strip mill product tolerances1. Thickness The thickness is measured at any point in the length of the coil (excluding uncropped front and tail ends as defined above), not less than 40mm from the untrimmed edge and 25mm from a side trimmed edge. Note:1. For patterned floor plate (VASTRAP ®) the thickness tolerances are increased by

Microalloyed high strength steels Arvedi Group

1) For thicknesses up to 2.5 mm maximum width is 1520 mm 2) Feasibility on the specific combination of thickness and width must be verified in the order phase S550MC / 1.0986 - SteelNumber - Chemical composition Chemical composition % of steel S550MC (1.0986):EN 10149-2-1996 The sum of Nb, V and Ti shall be max 0.22 % If agreed at the time of the enquiry and order the sulfur content shall be max 0.01 % S550MC steel - Steel GradesTool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S550MC Round Bar S550MC Flat Bar S550MC Hollow Bar S550MC Tube / Pipe S550MC Sheet / Plate S550MC Strip / Coil S550MC Wire S550MC Forging S550MC

S550MC steel,S550MC steel plate Shanghai Royal Industry

Thickness3mm L0=5.65S0. S550MC 550. 600-760 12 14. 1.5a. S550MC steel sheet size range. Grade. Size (mm) S550MC. 2.0~16.0 ×900~1750. S550MC steel plate/sheet application :S550MC steel for automobile beams have high strength and good bending performance, which is suitable for beam parts. The processes include cutting, punching Ship plate Tata Steel in EuropeTolerances on thickness for hot-rolled steel with a low carbon content for cold forming (DD11-DD14 in EN 10111:2008) Nominal thickness Tolerances for a nominal width of 1200 > 1200 > 1500 > 1800 1500 S550MC in EN 10149-2:1996) Tenform high-strength low-alloy steelS550MC 0.12 1.80 0.025 0.015 0.50 0.015 0.20 Note:Values are in weight percentages. Table 18:Dimensions:Tenform XK/XF Mill finish Thickness Width Min Max XF420 XK/XF350 XK/XF450 > XK/XF300 XK/XF400 XF460,XF500 XF550 1.50 1.60 710 1250 1100 1100 1.60 1.90 710 1425 1250 1250 1.90 2.10 710 1525 1300 1300 2.10 2.20 710 1600 1300

Tenform high-strength low-alloy steel

S550MC 0.12 1.80 0.025 0.015 0.50 0.015 0.20 Note:Values are in weight percentages. Table 18:Dimensions:Tenform XK/XF Mill finish Thickness Width Min Max XF420 XK/XF350 XK/XF450 > XK/XF300 XK/XF400 XF460,XF500 XF550 1.50 1.60 710 1250 1100 1100 1.60 1.90 710 1425 1250 1250 1.90 2.10 710 1525 1300 1300 2.10 2.20 710 1600 1300 Ympress S700MC Tata Steel in Europelength (in metres) = 90/nominal thickness (in mm), with a maximum of 20 metres. If required, this part of the coil can be removed, however an additional cost may be charged for this. Tolerances on thickness. Tata Steel can supply to full thickness tolerance specified in EN 10051:2010. Tighter tolerances are available as shown below: Ympress® S550MC Strong, consistent and highly formableproduct properties and reliable material thickness allow trouble-free, repeatable processing. Ympress® S550MC can be easily welded and galvanised. Its high surface quality can lead to fewer processing steps. Tolerances on thickness All Ympress® products comply to ½ EN 10051:2010. Tighter tolerances are available on request. Certification

productinformation precidur HSM 550 HD

® HSM 550 HD / S550MC Precision Steel Contents Brief portrait Technical features Chemical composition Mechanical properties General thickness tolerances Delivery options Application examples Microalloyed fine grain structural steel High ductility (HD) High scalur® pickled hot-rolled steel with very tight scalur ® s very tight tolerances fall far below the usual tolerances of hot-rolled strip. The calculation for our micro-alloyed steel S700MC serves as an example. The standardized tolerance thickness for micro-alloyed steel according to DIN EN 10051 amounts to +/- 0.29 mm at an ordered thickness of 2.10 mm. S550MC - Salzgitter Flachstahl GmbHS550MC High-strength steels for cold-forming, thermomechanically-rolled Available dimensions Hot-rolled coils unpickled, mill edge Thickness in mm Width in mm 2.00 2.99 900 300 3.00 3.99 900 450 4.00 6.00 900 500 Widths < 900 mm and thicknesses > 6.00 mm on request Hot-rolled slit strip Thickness in mm Width in mm

Get Price

We can supply you need s550mc thickness.